Banner Arms

Offering a variety of Banner Arms in both standard and breakaway style designs for use in both single and double sided applications. Our in house engineering team develops the safest and most efficient pole/banner arm combinations to match your project requirements.

PM Style Banner Arms

These arms use a cast aluminum mount welded to the pole shaft. The removable banner arm includes a flange that attaches to a cast mount via 2 hex head bolts and a removable cast aluminum ball cap.

Styles:

SBA: Single "PM" Style banner arm, mounts on same side of the pole.

DBA: Double "PM" Style banner arm, mounts on same side of the pole.

SBAR: Single "PM" Style banner arm AND ring, mounts on same side of the pole.

• Banner Am sizing:
  • 1/2" pipe (.84" OD) for banner arm lengths up to and including 20" long 
  • 3/4" pipe (1.05" OD) for banner arm lengths 21" to 30" 
• Please note:
  • For banner arm lengths longer than 30" should move to a HUB style banner arm
  • The actual banner width should be 2" smaller than the attachment arm , so an 18" wide banner is assumed to be used with a 20" long arm. (All Banners by Others)

HUB Style Banner Arms

These arms use an aluminum female coupling welded to the pole shaft. The removable banner arm includes a nut and bolt for a "cotter pin" style attachment to hub and a removable cast aluminum ball cap. 

Styles:

HSBA: Single Hub-Style banner arm, mounts on same side of the pole.

HDBA: Double Hub-Style banner arm, mounts on same side of the pole.

• Banner Am sizing:
  
  • 3/4" pipe (1.05" OD) for banner arm lengths up to 30" 
  • 1" pipe (1.315" OD) for banner arm lengths 31" to 38"
• Please note:
  • Max banner arm length is 38"
  • The actual banner width should be 2" smaller than the attachment arm , so an 18" wide banner is assumed to be used with a 20" long arm. (All Banners by Others)

CLAMP ON Style Banner Arms

These arms include a decorative 2-piece cast aluminum pole shaft attachment clamp with stainless steel hardware and a removable cast aluminum ball cap.

C_SBA: Single Clamp-Style banner arm, (1) Clamp and (1) Banner arm

C_2BA: Double Clamp-Style banner arms, (1) Clamp and (2) Banner arms @ 180 degrees

• Banner Am sizing:
  
  • 3/4" pipe (1.05" OD) for all sizes
• Please note:
  
  • These should be used on STRAIGHT poles ONLY (4" or 5" OD)
  • The actual banner width should be 2" smaller than the attachment arm , so an 18" wide banner is assumed to be used with a 20" long arm. (All Banners by Others)

BREAK-AWAY Style Banner Arms

These arms use an aluminum female coupling welded to the pole shaft. The removable banner arm includes a nut and bolt for a "cotter pin" style attachment to hub and a removable cast aluminum ball cap. 

BDBA_: Double Break-Away Style banner arms, mounts on same side of the pole.

• Banner Am sizing:
  
  • 3/4" pipe (1.05" OD) for 60 MPH break speed (BDBA6)
  • 1" pipe (1.315" OD) for 90 MPH break speed (BDBA9)
• Please note:
  
  • Engineered with a 60MPH maintained break speed (BDBA6), or a 90MPH maintained break speed (BDBA9)
  • Arm slides into a hub and is held in place with a cotter pin style mount
  • Includes an air-craft cable to hold broken section after incident
  • Hub is factory welded to pole shaft
  • This style is offered in standard sized, consult factory for custom sizes
    • Standard sizes include: 20"x36", 20"x72", 26"x48", 32"x36", 26"x60"
  • The actual banner width should be 2" smaller than the attachment arm , so an 18" wide banner is assumed to be used with a 20" long arm. (All Banners by Others)